Frequently Asked Questions

Use the Flat Panel Make and Model Number to search Artison’s Online Grille Listings to find the correct grille model number. Please find the link here: http://www.artisonusa.com/loudspeakers/lcr-grilles/

If the model number is not on the list, please e-mail your inquiry to support@artisonusa.com with the following information:

• Artison Speaker Selection
• Flat panel Manufacturer & Model Number
• Height of flat panel display without stand
• Bezel Color

Yes. The LCR-DM Bracket that comes attached to the speaker cabinet can be used to mount the speaker to the wall. Simply unscrew the thumbscrew knobs to remove the speaker from the Bracket, then utilize the slots in the back of the bracket to mount to the wall surface..

Yes. The SoundBar can be wall mounted with the included bracket, similar to the way the LCR-DM speakers attach to the wall. The SoundBar can also be placed on a shelf with the grille installed.

The Thin Universal Mounting Bracket (Thin UMB) in your LCR-DM box. These are pieces of Aluminum and Steel, which are intended to mount between the back of the television set and the television wall mount (Articulating Arm, Tilt or Static Mounts, etc.). If the television is not to be wall mounted the Thin UMB may be attached directly to the back of the television using the wall bracket mounting points. Using the supplied screws and washers, attach the two Brackets to the rear of the display. The Sliding Arms of the Thin UMB then adjusts to fit the width of your flat panel display set and provides mounting points for the Main LCR Bracket. For diagrams and details please refer to Page 4 of the LCR-DM Installation Guide.

Artison LCR-DM Speakers are compatible with Flat panels that range in depth from 0.28” - 4.5" Artison SoundBar is compatible with flat panels that are 3.5"-5.0" deep, and TV's that are 1.2" - 3.5" with the SoundBar Bent Bracket (SB1-BB) accessory.

The grilles are covered in Light Grey or Black Grille Cloth.

Grilles are all Made to Order to the exact TV height/width. The grilles you order should match the bezel height/width exactly.

The LRS Surrounds are Monopole below 3 KHz and Dipole above 3 KHz.

There is a steel wall-mounting plate attached to each speaker right out of the box. There are 4 ea. M3 screws that attach the LRS to the mounting plate. Remove these 4 screws using the supplied 3-mm Allen Wrench and the mounting plate can removed for wall or ceiling mounting.

Both DualMono Center Channel speakers are connected in parallel to the amplifier channel. Please refer to the diagram below.

Yes, refer to the diagram below. The nominal impedance will be ~10 Ohms per channel.

Notify Artison of the situation. If required, Artison will issue a RA number. Product returned without an RA Number will be refused.

Any good quality receiver will work. Please refer to power handling below for your Artison speaker.

Masterpiece LCR-DM: 125-250 Watts RMS set on THX, 80 Hz High Pass Crossover

Portrait LCR-DM: 75-150 Watts RMS set on THX, 80 Hz High Pass Crossover

Sketch LCR-DM: 75-150 Watts RMS set on THX, 80 Hz High Pass Crossover

SoundBar: 50-150 Watts RMS set on THX, 80 Hz High Pass Crossover

Masterpiece LCR In Wall: 50-250 Watts RMS set on THX, 80 Hz High Pass Crossover

Portrait LCR In Wall: 50-200 Watts RMS set on THX, 80 Hz High Pass Crossover

Sketch LCR In Wall: 50-150 Watts RMS set on THX, 80 Hz High Pass Crossover

LRS, LRS-IW: 50-150 Watts RMS set on THX, 80 Hz High Pass Crossover

Artison now offers a family of RCC In-Wall, In-Floor, and Freestanding Subwoofers for use with our other speaker products.

Please contact Artison at support@artisonusa.com and we will put you in contact with our sales representative in your area.